Classic Hanging Hardware Schematics
General Notes:
Actual track lengths are 1" less than 2x the nominal door width (i.e.. A 36" wide door would have a 71" track). Track standoffs are available for doors up to 2-1/4" thick. Doors more than 1" over typical sizes (i.e. 37" on a nominal 6' track) require the typical hanger offset be altered. See installation cut sheet for more information.
If your door is a custom size (i.e. 40"), you will have to reposition one end stop. Drill one hole at desired location and use hex bolt to fasten (NOT INCLUDED). You may also use adjustable end stops (Optional Accessory) or request a custom fabrication.
For bi-parting doors, butt the track of each kit end to end tightly. Joining tracks is not necessary.
General Notes:
Track must be installed into solid blocking or head casing.
Classic style weight ratings**
Steel Wheel: 400LBS
Hush Wheel: 400LBS
Wood Wheel: 80LBS
Classic Style Hanger
Aero Style Hanger
Standard Flat Track - SF - 06
Track Length: 71" (One-Piece Track)
Standard Flat Track - SF - 05.5 Track
Track Length: 65" (One-Piece Track)
Standard track lengths shown. Custom lengths available.
Note: Hole measurements are for general info only and not intended for use as a drilling template.
SA-C-GUIDE Door Guide
To install:
Determine how wide the door
'overlap' will be. The overlap is
the distance between the leading
edge of the door when fully open,
and the trailing edge of the door
when fully closed (1).
Mark centerline of overlap and
place center of guide on line (2).
Predrill and install on floor so door
will hang plumb.
General Notes:
For use when slotting the bottom of door for 'T' type guide is not desired or not possible.
Single mounting screw allows easy
installation and alignment.
Smooth, high strength glide plastic
guides door gently and quietly.
SA-T-Guide Door Guide
To install:
Determine how wide the door 'overlap' will be. The overlap is the distance between the leading edge of the door when fully open, and the trailing edge of the door when fully closed (1).
Mark centerline of the overlap and place center of guide on line (2).
Predrill and install on floor so door will hang plumb.
General Notes:
For use in wood doors when a semi-concealed look is desired.
Requires a 5/16"W x 1/2"H continuous slot in bottom of door.
Smooth, high strength glide plastic guides door gently and quietly.
Front View
Side View
Warning!
- Failure to wear proper safety gear (i.e., eye protection) may result in serious injury or death. Always wear proper safety gear before using power tools.
- Improper operation of power tools may result in loss of control, serious injury or death. Always ensure you have complete control of the power tool and the work area is free of hazards before operating any tool.
- Lack of secure clamping of the door may result in unexpected movement of the door, loss of power tool control and serious injury or death. Always securely clamp the door in place before cutting or drilling the door.
- Lack of nor improperly installed Anti-jump Disc may result in the door coming off the track and cause serious injury or death. Installation of Anti-jump Disks is required for the safe operation of this hardware. Installed correctly, these discs will keep the door securely attached to the track.
Caution!
- Mishandling of heavy objects (i.e., doors) may cause a loss of balance and severe injury. Always be sure you have a secure hold on the item and that the objects are balanced before moving. Always wear safety shoes when lifting heavy objects
- Getting body parts (i.e., hair, fingers) caught in moving parts may cause pinching and severe injury. Do not put fingers in parts that may move and always remove or contain anything on your body that may become entangled with a moving part.
- Closing sliding doors with your hand on the end of the door may result in your hand or fingers, getting caught between the door and other solid objects (i.e., another door, molding), causing severe injury. Always use the door handle to operate doors.